Expert Tips for Installing a New Shower Unit

Expert Tips for Installing a New Shower Unit

Blog Article

Schedule Free Estimate

How do you feel in relation to How to Install a Direct-to-Stud Shower Enclosure?

A successful shower installation requires careful planning and also a lot of job. Most of the times, you will require to do three types of tasks: framing wall surfaces, installing the plumbing, as well as ending up walls.

Prep work

Firstly, you need to decide on the sort of shower that you wish to set up. It is important to establish whether the picked shower is capable of handling particular systems as well as can control a secure degree of water via the boiler. Many shower systems nowadays are made to be versatile to different water pressures (such as kept hot water and cold mains).
It is also important to think about the water stress as well as the planning of the piping as well as drainage for the shower

Various Sorts Of Shower Units

Push-on Mixer: The pipe and also spray parts of the push-on mixer shower system can be linked to the bath faucet according to your requirement, and also the water temperature level can be readjusted via the taps. Push-on mixers are cheap and also extremely easy to set up. However, although the hose pipe connection is straightforward, it is conveniently dislodged. In addition, it is troublesome to adjust the temperature.

Bath/Shower Mixer: The tube as well as spray of this sort of shower are integrated with a bathroom mixer tap, as well as the temperature level can be changed via the bathroom taps. It is a really affordable alternative and no additional plumbing is entailed. However, the bath/shower mixers also experience troublesome temperature level control alternatives.

Manual Mixer: The hose and spray of a hands-on mixer shower system belong of the wall surface system and the hot and cold water supplies are connected to a solitary shutoff The temperature level and also stress of the water are regulated via either one or a selection of knobs (in more expensive showers). Although temperature control is a lot easier in hand-operated mixer kinds, they are a lot more costly than the previously mentioned mixers. They additionally call for added plumbing of hot and cold supply of water pipelines.

Thermostatic Mixer: The pipe and also spray of this shower kind are a part of the wall surface unit and also the cold and hot water products are attached to a solitary valve here also. It is total with an integrated stabiliser to self-adjust the water temperature and to avoid it from ending up being too warm. One of the most significant benefits of a thermostatic mixer shower type consists of hassle-free temperature control. Nonetheless, it is the most pricey of the different mixer alternatives.

Power Shower: A power shower is a single system containing an effective electric pump that is capable of modifying both the water pressure as well as temperature. This kind of shower can be fitted if there is water supply from a cold water cistern as well as a hot water cylinder. A power shower makes the modification of both stress as well as temperature level very easy. On the other hand, it disagrees for water warmed straight by the shower or where the water is provided by a mix boiler under keys pressure.

Electric Shower: An electrical shower is plumbed right into a mains cold water supply and also it heats the water electrically. It is very important to keep in mind that for this shower kind to be mounted, the keys stress needs to be a minimum of 0.7 kg/sq cm (10lb/sq in). The unit allows the temperature and also stress to be changed through a knob. Versions with temperature level stabilisers are much better as they remain unaffected by other taps in other places in use within the house. A major drawback of electric showers is that the control knob only permits the choice of heats at much less stress, or reduced temperature levels at a better pressure. This is problematic in the winter season when the spray is typically weak as well as the mains water is chillier. However, this problem is taken on in some versions which are offered with a winter/summer setting.

Method

Relying on the sort of shower you want to mount, the shower head have to either be suited order to prevent its contact with the water in the bath below or the base tray, or it should have a check shutoff.
Prior to beginning, it is advisable to mark the positions of the shower head as well as control, as well as to prepare the pipe-work included. In addition, the water drainage system to get rid of the drainage will certainly require to be intended. Both placements of the cord route and also the shower button will additionally require to be considered if an instant or electric shower system is being installed.
Utilize the instruction guide supplied with the shower unit to fit the shower control.Before fitting the pipelines that will supply the water to the shower system, it is important to cut off the water. In order to safeguard the pipelines, they should be provided a water-proof covering and likewise fitted with separating shutoffs. The pipelines can then be buried into the wall surface and also smudged over to neaten the overall appearance.
Fit the base tray, shower head, and also fittings.
Connect the main shower control to the pipes that will be supplying the water (This may need a female screw thread adapter).
Reconnect the water and also examination the pipelines for any kind of leaks, as some might require tightening.
If you are installing an electrical shower, bear in mind to turn off the power supply prior to making any electrical connections. When these connections have been made (there must be support within the user's manual), the power supply can be switched over back on.

Readjusting Water Stress to Suit Your Shower

The cold water reservoir can be raised to a better elevation (occasionally just 150mm (6inches)) by installation a solid wooden support underneath it - potentially composed of struts as well as blockboards. If you select this option, the primary and circulation pipelines will additionally need to be raised to satisfy the new height of the reservoir.
Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is picked, it must be connected right into the power supply in order to run.

Piping as well as Drainage

It is best to make use of 15mm size supply pipes, and also make the go to the shower as brief as well as straight as possible so regarding preserve maximum stress and reduce heat loss. In addition, by reducing using elbow joints for pipeline corners, you can lower the resistance in the flow of the water. You can achieve this by flexing the pipes instead.

Many Typical Mistakes

Violating or ignoring neighborhood code constraints.

Using pipes that are also tiny.

Affixing copper to galvanized without using a brass or dielectric fitting in between both.

Not making use of tape or pipeline substance at threaded joints.

Uneven your components when mounting them.

Not mounting an air void filling for fixtures.

Cutting supply stub outs also brief to set up the shutoff valves onto after the completed wall is in area.

Not correctly aligning tubes into installations or stop valves. (Requiring the nut onto the compression ring at an angle when the tubing is at an angle will trigger a leakage.).

When transforming the water back on in your home, always run the outside tube shutoff or purge your commodes to bleed dirt and air from the lines. This debris can trigger issues in your sink faucets as well as other plumbing trim.

How Do You Install a Shower? Follow This Guide

Installing a Shower at a Glance

Tools & Materials: Level, electric drill, caulk, hole saw, cedar shims, shower unit

Step 1: Drill pilot holes

Step 2: Prep fixture holes

Step 3: Move unit into place

Step 4: Caulk corners and base

Step 5: Attach door

Step 6: Install shower pan

Whenever plumbing is involved in a DIY project, people worry about what might go wrong. The truth is that installing a shower isn’t that complicated, and you can save a lot of money by doing it yourself. You shouldn’t need to make any alterations to your plumbing to complete the job, and most of the tools you need will be provided in your new shower kit.

Can I Install a Shower Myself?

Even if you’ve never installed a shower before, you’ll find this to be a project that is perfectly suited for DIYers with a moderate level of experience. Whether you're doing a bathtub conversion or installing a new stall, most of what you need comes in shower kits that you can purchase from a hardware store. The first thing you need to do is determine what type of shower stall you want.

Single-panel stalls are the easiest to install because they come preassembled. All you need to do is put them in place. Multi-panel showers require a few additional steps, but you’ve got more control over the appearance of your unit. Multi-panel units are also much easier to handle if you’re going to do the installation without any help.

Be sure to take all appropriate safety precautions, such as wearing eye protection and gloves. When you’re removing or installing a shower unit, you might kick up debris that could hurt your eyes. You’ll also need to work with equipment that will get extremely hot, so be sure to have safety gloves handy.

Tools and Materials

2- to 4-foot level

Electric drill with a 1/8-inch drill bit

Caulk

2-inch hole saw

Cedar shims

The unit itself

Before You Begin: Prep the Space

It’s highly important to measure your space accurately before putting the stall in. Measuring from the floor upward and from each corner outward will ensure you’ve got the right measurements. What you’re looking for is where the plumbing apparatuses are going to come through the stall. Transfer these measurements over to the back of your unit by drawing the locations of these holes using a pencil or marker.

Pull out your old shower and make sure to scrape off all the old caulking. Be thorough because you want to work with smooth surfaces for the best installation. Once you’ve pulled out your existing shower, you need to make sure that the floor is clean and dry. The best way to clean debris is with a shop vacuum, as it’ll soak up water and dirt together.

If you’re experiencing any plumbing issues, such as low water pressure, this is a perfect opportunity to solve them. Make sure that the pipes themselves are not in need of patching and clean your showerhead. When you turn the water back on after your project, check the pipes for signs of wear or disrepair. Anything beyond minor repairs should be handled by a plumber, and this is the best time to bring in a professional.

If the floor has any moisture at all, don’t proceed until it’s completely dry. The last thing you need is for the floor to rot or invite mold and mildew into your base. Once everything is dry, apply waterproof wallboard to the walls. This can be attached with screws or nails, then sealed with caulk so that water doesn’t seep into any crevices.

https://www.homeserve.com/en-us/blog/how-to/install-shower/

As a fervent reader on How to Build a Shower Enclosure for Your DIY Bathroom, I assumed sharing that piece of content was worthwhile. Enjoyed our content? Please share it. Help other people locate it. Many thanks for your time spent reading it.

Call Today

Report this page